Fixing the Wi-Fi connection.

[Ctrelok_Cvobods]

Hello.

Approximate Name:
Network Connection: Network Switch.

What does:
Tries to connect to one of the saved Wi-Fi zones in turn.

Why is this necessary:
There is a Xiaomi Android device below 10 (a friend), where Wi-Fi is turned on, but does not look for points until you go into the settings (I think it's a mistake of a separate device).
Therefore, I created a macro (attached in files) that counts the Wi-Fi networks I have added in turn and searches endlessly for the available one (if Wi-Fi is enabled and the network is not found).
The problem is that I could not find a universal action that allows you to switch Wi-Fi networks in turn from the list of settings already saved on the device, which is displayed when you select the "Connect to connection" action settings. Because if you connect to a new Wi-Fi network without adding it to the macro, it will be ignored, and you will have to re-enter the settings as it is happening now (which slightly infuriates my friend).
If there was an action that I suggest, it would be possible to fix the bug. I have already tested and got the result: if you specify in the macro which Wi-Fi network you need to connect to, there is no glitch.

*Unfortunately, my English is bad, so I had to translate through a translator.

 

[Dm114]

Здравствуйте.

Приблизительное название:
Сетевое подключение: Коммутатор сети.

Точка:
Пытается подключиться к одной из сохраненных зон Wi-Fi по очереди.

Зачем это нужно:
У меня есть простой макрос, который включает Wi-Fi.
Многим друзьям и родственникам я добавил этот макрос, но на одном из устройств Xiaomi Android ниже 10 Wi-Fi включается, но не ищет точки, пока вы не зайдете в настройки (я считаю ошибкой отдельного устройства).
Поэтому я создал макрос (прикрепленный в файлах), который по очереди подсчитывает добавленные мной сети Wi-Fi и бесконечно ищет доступную (если Wi-Fi подключен, а сеть не найдена), но я хотел увидеть возможность переключения между списком сохраненных сетей Wi-Fi.Автоматически (без списка, который я добавил в макрос). Поскольку, если вы подключитесь к новой сети Wi-Fi, не добавив ее в макрос, она будет проигнорирована в макросе, и вам придется повторно ввести настройки, чтобы исправить ошибку телефонной системы.

If you want to get help from the whole MD community, please write in English.

If you can't, use a translator.

 

[Ctrelok_Cvobods]

Translated the text.
The built-in translator in the browser translated the text itself, but I didn't notice it and sent it.

 

[Dm114]

Hello.

Approximate Name:
Network Connection: Network Switch.

What does:
Tries to connect to one of the saved Wi-Fi zones in turn.

Why is this necessary:
There is a Xiaomi Android device below 10 (a friend), where Wi-Fi is turned on, but does not look for points until you go into the settings (I think it's a mistake of a separate device).
Therefore, I created a macro (attached in files) that counts the Wi-Fi networks I have added in turn and searches endlessly for the available one (if Wi-Fi is enabled and the network is not found).
The problem is that I could not find a universal action that allows you to switch Wi-Fi networks in turn from the list of settings already saved on the device, which is displayed when you select the "Connect to connection" action settings. Because if you connect to a new Wi-Fi network without adding it to the macro, it will be ignored, and you will have to re-enter the settings as it is happening now (which slightly infuriates my friend).
If there was an action that I suggest, it would be possible to fix the bug. I have already tested and got the result: if you specify in the macro which Wi-Fi network you need to connect to, there is no glitch.

*Unfortunately, my English is bad, so I had to translate through a translator.

I prefer Dev to answer but I don't think it's possible.